CADLisp Tools

Text & Numbering

Change Text Case AutoLISP routine

Convert selected TEXT and unformatted MTEXT to upper- or lowercase. Download the .LSP source below and run the TEXTCASE command after loading it.

⌘ TEXTCASEv1.1.0BeginnerUpdated Sep 18, 2026

What it does

Change Text Case with the TEXTCASE AutoLISP command

Applies a consistent case to a deliberate selection of drawing text without altering its position, style, layer, or MTEXT formatting controls.

AutoLISP command
TEXTCASE
Difficulty
Beginner

Applicable disciplines

CAD workflows that use this routine

Requirements and compatibility

What it needs

AutoLISP

Software rows marked “Not tested” are not compatibility claims. Test the routine in a copy of your drawing and CAD version.

Downloadable source code

Review the change-text-case.lsp AutoLISP code

change-text-case.lspAUTOLISP
;; CADLisp Tools - Change Text Case
(defun ct-tc:editable-p (data / row flags)
  (and data
       (setq row (tblsearch "LAYER" (cdr (assoc 8 data))))
       (setq flags (cdr (assoc 70 row)))
       (= 0 (logand flags 20))))

(defun ct-tc:text-value (data / pair value)
  (setq value "")
  (foreach pair data
    (if (member (car pair) '(1 3)) (setq value (strcat value (cdr pair)))))
  value)

(defun ct-tc:control-code-p (value / character found index)
  (setq index 1 found nil)
  (while (and (not found) (<= index (strlen value)))
    (setq character (substr value index 1)
          found (member character '("\\" "{" "}"))
          index (1+ index)))
  (if found T nil))

(defun ct-tc:formatted-mtext-p (data value)
  (and (= (cdr (assoc 0 data)) "MTEXT") (ct-tc:control-code-p value)))

(defun ct-tc:text-pairs (value / pairs)
  (setq pairs nil)
  (while (> (strlen value) 250)
    (setq pairs (cons (cons 3 (substr value 1 250)) pairs)
          value (substr value 251)))
  (reverse (cons (cons 1 value) pairs)))

(defun ct-tc:set-value (data value / inserted item new out pair)
  (setq inserted nil new (ct-tc:text-pairs value) out nil)
  (foreach pair data
    (if (member (car pair) '(1 3))
      (if (not inserted)
        (progn
          (foreach item new (setq out (cons item out)))
          (setq inserted T)))
      (setq out (cons pair out))))
  (reverse out))

(defun c:TEXTCASE (/ *error* changed data ent i lower mode old skipped ss undo-started)
  (defun *error* (message)
    (if undo-started (command-s "_.UNDO" "_End"))
    (if (and message (not (wcmatch (strcase message) "*CANCEL*,*QUIT*,*EXIT*")))
      (prompt (strcat "\nTEXTCASE error: " message)))
    (princ))
  (initget "Upper Lower")
  (setq mode (getkword "\nCase [Upper/Lower] <Upper>: ") lower (= mode "Lower"))
  (prompt "\nSelect TEXT or unformatted MTEXT: ")
  (if (setq ss (ssget '((0 . "TEXT,MTEXT"))))
    (progn
      (setq changed 0 skipped 0)
      (if (= 0 (logand 8 (getvar "UNDOCTL")))
        (progn (command "_.UNDO" "_Begin") (setq undo-started T)))
      (repeat (setq i (sslength ss))
        (setq ent (ssname ss (setq i (1- i))) data (and ent (entget ent))
              old (and data (ct-tc:text-value data)))
        (if (and (ct-tc:editable-p data) old (not (ct-tc:formatted-mtext-p data old))
                 (entmod (ct-tc:set-value data (strcase old lower))))
          (progn (entupd ent) (setq changed (1+ changed)))
          (setq skipped (1+ skipped))))
      (if undo-started (progn (command "_.UNDO" "_End") (setq undo-started nil)))
      (prompt (strcat "\nUpdated " (itoa changed) " object(s); skipped " (itoa skipped)
                      " locked, referenced, invalid, or formatted MTEXT object(s).")))
    (prompt "\nNo text selected."))
  (princ))

Setup

How to install the change-text-case.lsp file

  1. 1Download and review the source code.
  2. 2Load the .lsp file with APPLOAD in a copy of a drawing.
  3. 3Keep the routine session-only until it has been tested for your CAD version and standards.

Command workflow

How to run the TEXTCASE command

  1. 1Run TEXTCASE.
  2. 2Choose Upper or Lower.
  3. 3Select TEXT or unformatted MTEXT and press Enter.

Worked example

Example: Standardize a group of notes to uppercase.

  1. Run TEXTCASE.
  2. Choose Upper.
  3. Select the notes.
Expected result

Editable plain text is uppercase; formatted MTEXT is reported as skipped.

Read before use

Notes and limitations

  • Does not provide title case.
  • Skips MTEXT containing backslash or brace control codes to avoid corrupting formatting.
  • Skips locked, xref-layer, and invalid entities.
  • Not manually CAD-tested.

Version history

Changelog

v1.1.0Sep 18, 2026Preserve long MTEXT, skip formatting controls safely, and add undo/error handling.
v1.0.0Sep 18, 2026Initial upper/lowercase routine.

Keep automating

Related tools

Text & Numbering6 disciplines

Add Prefix to Selected Text

Add a fixed prefix to selected TEXT and MTEXT objects.

⌘ ADDPREFIXBeginnerCAD support: not tested
Updated Sep 18, 2026VIEW TOOL →
Text & Numbering6 disciplines

Add Suffix to Selected Text

Append a fixed suffix to selected TEXT and MTEXT objects.

⌘ ADDSUFFIXBeginnerCAD support: not tested
Updated Sep 18, 2026VIEW TOOL →
Text & Numbering6 disciplines

Find & Replace Selected Text

Replace matching text inside a deliberate selection of TEXT and MTEXT objects.

⌘ REPTEXTIntermediateCAD support: not tested
Updated Sep 18, 2026VIEW TOOL →